Department of Defense (DoD) information assurance (IA) through a Authorizes the publication of DoD M consistent with DoD TITLE: DoD Directive , “Information Assurance (IA),” 10/24/ SUMMARY: This Directive: 1. Establishes policy and assigns. What changed between -DoD Directive Information Current DOD Instruction , Cybersecurity was signed March 7,
|Published (Last):||22 June 2013|
|PDF File Size:||20.40 Mb|
|ePub File Size:||1.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
Department of Defense DoD and its closer alignment with cybersecurity initiatives and standards in other parts of the Government. Note that overlays are baseline-independent, meaning that they can be applied to any NSS baseline e.
For example, under the HIGH potential impact: Tailoring modifies and aligns the initial control set to more closely account for conditions affecting the specific system i. A severe or catastrophic adverse effect means that, for example, the loss of confidentiality, integrity, or availability might: It is presented in depth in Part 2. It is a reissuance and renaming of DoDI This is discussed further below and will 8500. more apparent in Figure 2. Highlighting some of these changes:.
DoD Instruction 8500.1 – Cybersecurity report
Part 2, Cybersecurity and the U. Tailoring the Initial Security Control Set Tailoring modifies and aligns the initial control set to more closely account for conditions affecting the specific system i.
Levels 85001 increasingly controlled unclassified information. These are discussed in Part 2. Security controls for all six levels do rely upon FedRAMP as their basis, but each level adds further controls and enhancements.
Highlighting dodii of these changes: Key References in DoD Cybersecurity: As noted, the subject of DODI Identifying overlays that apply to the IS and its operating environment to account for additional factors beyond impact that influence the selection of security controls. As discussed in Part 2, FedRAMP is a Government-wide program that provides a standardized approach to security assessment, authorization, and continuous monitoring for cloud products and services.
Department of Defense and all NSS.
Guidance on Information System Security Control Selection, RMF Step 2 Once the security categorization of the IS is complete, the general steps to security control selection are selecting the initial security control set and then tailoring its elements. The single-word subject of DoDI If so, tailor the set of controls accordingly. Part 1, Cybersecurity Overviewprovided a general introduction to cybersecurity and introduced many of the basic terms pertaining to attack and defense.
DoD Cybersecurity: CNSSI , DoDI , etc.
There are two levels of SGR, core more conceptual and technology. Once the security categorization of the IS is complete, the general steps to security control selection are selecting the initial security control set and then tailoring its elements.
Of note in Enclosure 1, References, is the inclusion of: All of the above is to be documented in the security plan. Level 6 is for classified information. Incorporated by reference in DoDI Document the dodk in the security plan.
For example, 8500.1 include: Part 3 of our three-part cybersecurity tutorial Part 1Part 2 has focused on cybersecurity and the U. Overlays address additional factors beyond impact or diverge from the assumptions used to create the security control baselines.
Importantly, we note dodu acceptance of NIST standards as the baseline of NSS security policy and controls, upon which additional controls dodl policies are placed for the special requirements of NSS. If you want to watch the video version of Part 3, look for it at the bottom of the cybersecurity landing page. Determine whether or not additional assurance—related controls are needed to increase the level of trustworthiness in the information system.
Guidance for the additional controls is provided in Table D-2, a portion of which is shown as Figure 3. Summary of Part 3 Part 3 of our three-part cybersecurity tutorial Part 1Part 2 has focused on cybersecurity and the U. As outlined in CNSSIpreserving the three discrete components, rather than using the HWM, provides granularity in allocating security controls to baselines and reduces the need for subsequent tailoring.
Apply any overlay s identified as applicable during security categorization, RMF Step 1. STIGs document dodu DoD policies and security requirements for specific technical products, as well as best practices and configuration guidelines.