CCNA 3 Final Exam Answers version v – % Full, CCNA v5. v The new switch has a VTP revision number of 4. CCNA v Routing and Switching Exam Answers , Free CCNA Study Guide, Tutorials, Labs, Practice Exams. CCNA Security, , v CCNA 2 v Capitulo 4 Examen Online en Español Cisco CCNA 1 Capitulo 4 Examen Pregunta 13 Cisco CCNA2 v Capítulo 3 Examen Pregunta
|Published (Last):||22 November 2009|
|PDF File Size:||11.36 Mb|
|ePub File Size:||13.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
Which switch will become the root for VLAN 20? A network administrator configures a switch port with the command switchport mode dynamic auto. While configuring a new switch, a network administrator configures the switch as an HTTP server.
Which two settings show the default value of VTP configuration on a Cisco switch? The enable password is configured as cisco. Whenever an inter-switch link fails, the network takes nearly a minute to completely dsscargar. What two methods can be used to cca MAC address table entries from a switch?
CCNA 3 Final Exam V4.0 Answers
The default gateway is not on the same switch that the PC is. VTP currixula is disabled. Why do you need a router if there both curridula the same vlan? January 24, at 7: All switch ports are assigned to VLAN1. Users who are assigned to VLAN 10 are connected as shown in the exhibit. Which hosts will receive the collision jamming signal? It segments a network into multiple broadcast domains.
What do you think guys? What will be the result of the student making this connection? This allows remote VPN connections to the switch over the Internet.
Examenes Cisco CCNA v en Español
October 13, at 8: Host A can communicate with host B, but cannot communicate with host C or host D. This allows web-based configuration tools to be used descarfar the switch. Easily MAC addresses are spoofed. April 9, at 2: From a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser.
My Del Mar College.
CCNA 3 Final Exam V Answers
All inter-switch links that are shown are trunks. Reply Marcelo Soares says: March 8, at 1: November 30, at 8: October 6, at 5: A successful trunk will be established if the remote switch is non-Cisco but the port is configured for trunking.
Associate with the access point and then open a HyperTerminal session with the access point. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. VTP v2 is disabled. The result is that frames are being dropped. The command should have been copy startup-config tftp: SW1 encapsulates the traffic with Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical network.
Which configuration changes will increment the configuration revision number on the VTP server?
What benefits does this configuration provide? Switches in the existing office and the new office are directly connected by a trunk link.
The first VTY chrricula is automatically configured to allow remote connections. Attach the web server to a router and configure inter-VLAN routing. It is sending and receiving data frames. When the auto-MDIX feature is enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly.
August 7, at 8: It is receiving BPDUs, but not sending data frames. Allow all VLANs on the trunk link.
What will commonly cause this problem? All trunk links are operational and all VLANs are allowed on all trunk links. Users complain that they do not have connectivity to the web server that is descwrgar to SW1. What is true of the configuration of switch S1?
SW1 leaves the traffic untagged and forwards it over the trunk. The PC is set to full duplex. October 17, at 3: