ASTM-A › Zinc Coating (Hot-Dip), Assembled Steel Products. ASTM-A – EDITION – SUPERSEDED — See the following: ASTM-. in Specifications A and A This ASTM Standards A47/ A47M 1 This specification is under the jurisdiction of ASTM Committee A05 on. ASTM AAM Standard Specification for Zinc – Standard A and A shall be done using the metric equivalent of the test.
|Published (Last):||20 May 2010|
|PDF File Size:||15.80 Mb|
|ePub File Size:||12.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
The average of the? NOTE 4—The coating thickness grades in Table 1 represent the minimum value obtainable with a high level of con?
ASTM A – Withdrawn Specification for Zinc Coating (Hot-Dip) on Assembled Steel Products
The use of these trace elements is permitted provided that the bulk chemistry of the galvanizing bath is at least ASTM specifications represent a consensus among producers, specifiers, fabricators, and users of steel mill products. The other values are based on conversions using the following formulas: In the case of orders in SI units, the values in Table 1, shall be applicable as metric units in micrometres.
Where products consisting of various material thicknesses or categories are galvanized, the coating thickness grades for each thickness range and material category of material shall be as shown in Table 1.
In the case of orders in SI units, all testing and inspection 1 This speci? The test method for the a3886 sample shall be selected by mutual agreement between the purchaser and galvanizer.
Consultation between the designer, fabricator, and galvanizer at appropriate stages in the design and fabrication process will reduce future problems.
The weight of coating per unit area thus determined is converted to equivalent coating thickness values according to Table 2 rounding up or down as appropriate. Do not use testing carried out at edges or corners points of lowest coating adhesion to determine adhesion of the coating. In the case of any such article containing more than one material category or steel thickness range as delineated in Table 1, that article will contain more than one specimen see Fig. In the case of orders in inch-pound units, the measured value shall be asttm to coating grade units by the use of Table 2.
The zinc coating on threaded components of articles galvanized under this speci?
ASTM B standard spe A number in parentheses indicates the year of last reapproval. Finding ASTM materials and standards from specific designation systems in the Total Materia database With Total Materia finding information about a metal standard specification, its current status and the materials it defines is one click away.
The pieces shall be handled so that after galvanizing they will not freeze together on cooling.
NOTE 2—The presence in asgm and weld metal, in certain percentages, of some elements such as silicon, carbon, and phosphorus tends to accelerate the growth of the zinc-iron alloy layer so that the coating may have a matte? Enter a phrase to search for: The thickness of coating thus obtained is the test article coating thickness, or in the case of a specimen removed from a test article, is the specimen average coating thickness. DataPLUS, a new module providing corrosion data, material joining information, material dimensions and tolerances and coatings information helps drive even more accurate material selections!
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Likewise, do not use removal of small particles of the coating by paring or whittling to determine failure.
The requirements for malleable iron castings to be galvanized shall be as stated in Speci? NOTE 6—The requirements for the? Dynamic Strain Aging of Steels: A superscript epsilon e indicates an editorial change since the last revision or reapproval. Originally published as A — 28 T.
ASTM Standard List: Coated Steels
Introduction to Total Materia 7 th February However, by agreement the purchaser is not prohibited from making tests which govern the acceptance or rejection aatm the materials in his own laboratory or elsewhere. If a sample is taken as representing the lot for acceptance, the sample shall be taken at random from the lot without regard to the perceived quality or appearance of any individual unit in the lot being sampled.
This standard has been approved for use by agencies of the Department of Defense. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
For each specimen as described in 3. Introduction to Total Materia Integrator 7 th March NOTE 9—Although some material may be formed after galvanizing, in general the zinc coating on the articles covered by this speci?
Such inaccessible areas, for example, would be the internal surfaces of certain tanks, poles, pipes, tubes, and so forth. For purposes of this speci? The thickness thus determined is a point value. The result list consists of over ASTM metal standards.