ALIGN 3GX 2.1 MANUAL PDF

The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Gunris Gabei
Country: China
Language: English (Spanish)
Genre: Travel
Published (Last): 1 January 2015
Pages: 416
PDF File Size: 8.49 Mb
ePub File Size: 18.9 Mb
ISBN: 465-9-37169-820-1
Downloads: 44868
Price: Free* [*Free Regsitration Required]
Uploader: Samugar

Should any changes made to the endpoints or subtrims on the transmitter in the future, the 3GX flybarless system initial setup must be performed again. The good news is if its a Futaba S-bus receiver then it is capable of using s-bus allgn one wire to control the lot. With all channels stationary, move the transmitter elevator stick forward, and then back to center position. The more dampening effect, the smoother helicopter flies, but feels less direct.

This completes the flybarless portion of the setup process. Then you remove the bind plug and power down. LIM setup While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter E.

Feb 05, Remove Advertisements Sponsored Links. Set the right aileron and front elevator to 8 degrees. Posting Quick Reply manuql Please Wait. I spoke to the UK distributor today about my problem, and after a while we agreed that it seemed like the channel 6 servo was behaving as if it had a curve programmed to it. The control unit will determine the maximum aileron endpoints. Posting Quick Reply – Please Wait.

3GX Flybarless System – Download – Align

While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter E. Press the SET button to enter A. Gyro gain For radio with built in gyro gain settings, gain can be adjusted directly.

  ENVIRONMENTAL SCIENCE MILLER SPOOLMAN 13TH EDITION PDF

Confirm the rudder settings by pushing the SET button. I built my T-Rex during the week, and got a receiver for it yesterday, but I’m now having a problem setting up the flybarless system.

Check that there is no binding throughout the pitch range 4. Anything else I should try, please, before telling the vendor that the unit’s bad? Password Please enter a password for your user account.

Just leave the servo horns off until your in setup and install them as close to level as poss at mid stick. I mean like if you get a e super combo new, it comes with the connection wires? Press the SET button to enter E.

Check if the rudder servo is applying correct compensation to the right.

Therefore, BEC output capability should be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply may result in flight accidents. Aileron and elevator rates can be adjusted in 3GX panel algin cyclic pitch rate adjustment under flight mode settings.

Check that there is no binding throughout the pitch range 3.

At least its identical to my manual that starts on page Based on the 3G FL manual setup process, the 3GX can be setup in a few minutes through a simple process. Mostly for my own memory. Fail safes set wrong can cause your helli to spool up if there is a loss of connectivity with the TX.

Align 3gx pdf manual

Lift up the helicopter by hand, and turn it to the left yaw. Def hook up power to the unit, get a usb extension cable and hook it to your pc and it almost walks you through the setup process. mnual

  ANTRENAMENTUL AUTOGEN SCHULTZ PDF

If ava ilable, ensure the following functions are disabled in the transmitter: The superior vibration resistant characteristic is evident even when mounted with harder double sided mounting tape.

For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate aligb non-heading lockor press and hold the SET button for 2 seconds.

There is a direct correlation between servos’ speed to gyro’s performance. If you use the software there are text and pop-ups to explain the settings: Anti-torque To achieve consistent alibn gain on left and right, 3GX has built in anti-torque compensation function.

Reset throttle curve and pitch curve to default Feb 04, Subsequent setup mode is entered by 33gx single press of the SET button. Also you cant update the mnaual with your transmitter lol. Sign up now to remove ads between posts. The recommended collective pitch range for various T-Rex helicopters is degress depending on preferenses.

Anyway, after talking a while, with the manual in front of me, it dawned on me mankal there’s an error in the manual; on page 21 it shows the 3Gx connection to a Futaba RFS receiver, which is what mine is, as being red, orange, yellow, green, blue, purple in that order, from channel 1 to 6.

With all channels stationary, move the transmitter aileron stick to the right and then back to center position. This completes the rudder endpoint limit adjustment for the right side. Originally Posted by Tulo I mean like if you get a e super combo new, it comes with the connection wires? That’s kinda what I figured thanks!